maimaiTouchControl/config.h

class touchblock
{
public:
  uint8_t mprid;
  uint8_t portid;
  int8_t thresOffset;
};

const uint8_t MPR_PADNUMS[] = {8, 9, 9, 8};
const uint8_t THREASHOLD = 35;

touchblock touchmap[34] = {
    // Group A
    {3, 4, 0}, // 1
    {3, 0, 0}, // 2
    {2, 4, 0}, // 3
    {2, 0, 0}, // 4
    {1, 5, 0}, // 5
    {1, 0, 0}, // 6
    {0, 4, 0}, // 7
    {0, 0, 0}, // 8
    // Group B
    {3, 5, 0}, // 1
    {3, 1, 0}, // 2
    {2, 5, 0}, // 3
    {2, 1, 0}, // 4
    {1, 6, 0}, // 5
    {1, 1, 0}, // 6
    {0, 5, 0}, // 7
    {0, 1, 0}, // 8
    // Group C
    {2, 8, 0}, // 1
    {1, 2, 0}, // 2
    // Group D
    {3, 6, 0}, // 1
    {3, 2, 0}, // 2
    {2, 6, 0}, // 3
    {2, 2, 0}, // 4
    {1, 7, 0}, // 5
    {1, 3, 0}, // 6
    {0, 6, 0}, // 7
    {0, 2, 0}, // 8
    // Group E
    {3, 7, 0}, // 1
    {3, 3, 0}, // 2
    {2, 7, 0}, // 3
    {2, 3, 0}, // 4
    {1, 8, 0}, // 5
    {1, 4, 0}, // 6
    {0, 7, 0}, // 7
    {0, 3, 0}, // 8
};

// the release threashold will be set to THREASHOLD - RELEASE_THREASHOLD_OFFSET
const uint8_t RELEASE_THREASHOLD_OFFSET = 0;

// AN3944 recommended values are:
// MHDR = 1
// NHDR = 1
// NCLR = 0
// FDLR = 0
// MHDF = 1
// NHDF = 1
// NCLF = 255
// FDLF = 2
// dk values are:
// MHDR = 1
// NHDR = 16
// NCLR = 4
// FDLR = 0
// MHDF = 4
// NHDF = 1
// NCLF = 16
// FDLF = 4
const uint8_t MHDR = 2;
const uint8_t NHDR = 2;
const uint8_t NCLR = 4;
const uint8_t FDLR = 0;
const uint8_t MHDF = 2;
const uint8_t NHDF = 1;
const uint8_t NCLF = 32;
const uint8_t FDLF = 4;

// range: 0 - 3
// 0: 6 samples
// 1: 10 samples
// 2: 18 samples
// 3: 34 samples
// aka. first filter averaging samples
// the highest and lowest are tossed
// so theoretically, the less samples, the system is less prone to noise
const uint8_t FIRST_FILTER_ITERATIONS = 0;

// range: 0 - 7
// actual value is 2^(CDT-1) us
// will be overriden by autoconfig, unless SCTS is set to 1
const uint8_t CHARGE_DISCHARGE_TIME = 1;

// range: 0 - 3
// 0: 4 samples
// 1: 6 samples
// 2: 10 samples
// 3: 18 samples
// aka. second filter averaging samples
const uint8_t SECOND_FILTER_ITERATIONS = 0;

// range: 0 - 7
// 2^ESI ms of first stage samples are taken into account
// all the first stage samples in the period is averaged
const uint8_t ELECTRODE_SAMPLE_INTERVAL = 0;

// range: 0 - 7
// when DR + 1 samples are lower than the threshold, the electrode is released
const uint8_t RELEASE_DEBOUNCE = 1;

// range: 0 - 7
// when DT + 1 samples are higher than the threshold, the electrode is touched
// a debounce value that's too low might cause touches that's too short to be missed
const uint8_t TOUCH_DEBOUNCE = 1;
// ! the touch response time is debounce * SFI * ESI ms
// ! so in the code bellow we set read interval to SFI * ESI ms

// please refer to AN3889 page 9 for more information
const uint8_t AUTO_CONFIG_RETRY = 0;
const uint8_t AUTO_CONFIG_BVA = 2;
const uint8_t AUTO_CONFIG_ARE = 1;
const uint8_t AUTO_CONFIG_ACE = 1;

// @datasheet page 15 and 18
// setting this to 1 disables CDT search
// which means it will use a fixed CDT and only search for CDC
// this results in a known first stage sample amount
// however, through testing, setting this to 1 will greatly degrade signal quality
const uint8_t SCTS = 0;

// those values are suitable for 3.3V, for other voltage systems, please refer to AN3889 page 7 through 8
const uint8_t USL = 202;
const uint8_t TL = 182;
const uint8_t LSL = 131;

// please refer to page 16 of the datasheet for more information
const uint8_t CALIBRATION_LOCK = 0x10;